Experimental Study of a Command Governor Adaptive Depth Controller for an Unmanned Underwater Vehicle

Unmanned Underwater Vehicles (UUVs) are increasingly being used in advanced applications that require them to operate in tandem with human divers and around underwater infrastructure and other vehicles. These applications require precise control of the UUVs which is challenging due to the non-linear and time varying nature of the hydrodynamic forces, presence of external disturbances, uncertainties and unexpected changes that can occur within the UUV’s operating environment. Adaptive control has been identified as a promising solution to achieve desired control within such dynamic environments. Nevertheless, adaptive control in its basic form, such as Model Reference Adaptive Control (MRAC) has a trade-off between the adaptation rate and transient performance. Even though, higher adaptation rates produce better performance they can lead to instabilities and actuator fatigue due to high frequency oscillations in the control signal. Command Governor Adaptive Control (CGAC) is a possible solution to achieve better transient performance at low adaptation rates. In this study CGAC has been experimentally validated for depth control of a UUV, which is a unique challenge due to the unavailability of full state measurement and a greater thrust requirement. These in turn leads to additional noise from state estimation, time-delays from input noise filters, higher energy expenditure and susceptibility to saturation. Experimental results show that CGAC is more robust against noise and time-delays and has lower energy expenditure and thruster saturation. In addition, CGAC offers better tracking, disturbance rejection and tolerance to partial thruster failure compared to the MRAC.     

Dynamic modelling of retrogressive landslides with emphasis on the role of clay sensitivity

This paper presents a detailed numerical study of the retrogressive failure of landslides in sensitive clays. The dynamic modelling of the landslides is carried out using a novel continuum approach, the particle finite element method, complemented with an elastoviscoplastic constitutive model. The multiwedge failure mode in the collapse is captured successfully, and the multiple retrogressive failures that have been widely observed in landslides in sensitive clays are reproduced with the failure mechanism, the kinematics, and the deposition being discussed in detail. Special attention has been paid to the role of the clay sensitivity on each retrogressive failure as well as on the final retrogression distance and the final run‐out distance via parametric studies. Moreover, the effects of the viscosity of sensitive clays on the failure are also investigated for different clay sensitivities.     

A multiscale work-analysis approach for geotechnical structures

This paper presents a second-order work analysis in application to geotechnical problems by using a novel effective multiscale approach. To abandon complicated equations involved in conventional phenomenological models, this multiscale approach employs a micromechanically-based formulation, in which only four parameters are involved. The multiscale approach makes it possible a coupling of the finite element method (FEM) and the micromechanically-based model. The FEM is used to solve the boundary value problem (BVP) while the micromechanically-based model is utilized at the Gauss point of the FEM. Then, the multiscale approach is used to simulate a three-dimensional triaxial test and a plain-strain footing. On the basis of the simulations, material instabilities are analyzed at both mesoscale and global scale. The second-order work criterion is then used to analyze the numerical results. It opens a road to interpret and understand the micromechanisms hiding behind the occurrence of failure in geotechnical issues.     

Application of micropolar plasticity to post failure analysis in geomechanics

A micropolar elastoplastic model for soils is formulated and a series of finite element analyses are employed to demonstrate the use of a micropolar continuum in overcoming the numerical difficulties encountered in application of finite element method in standard Cauchy–Boltzmann continuum. Three examples of failure analysis involving a deep excavation, shallow foundation, and a retaining wall are presented. In all these cases, it is observed that the length scale introduced in the polar continuum regularizes the incremental boundary value problem and allows the numerical simulation to be continued until a clear collapse mechanism is achieved. The issue of grain size effect is also discussed. Copyright © 2004 John Wiley & Sons, Ltd.     

浅谈项目投资失败的原因及对策

地勘单位在向企业化经营转变的过程中 ,投资兴办了许多企业 ,但不少项目以失败告终。文章分析探讨了失败的原因 ,并提出相应的对策     

富碳拱星IRC＋10216和CIT6的CO J=1—0转动谱的观测

使用中国科学院紫金山天文台青海站13.7米射电望远镜于1996年12月至1997年1月对富碳拱星IRC 10216和CIT6的CO J=1-0跃迁(115GHz)进行了观测。在观测谱线的基础上得到了IRC 10216的视向速度和膨胀速度分别为一26.1km s~(-1)和14.8km s~(-1),CIT6的视向速度和膨胀速度分别为0.6km s~(-1)和13.8kms~(-1)。并对望远镜的射束及指向精度进行了研究。     

Analysis of mapping coverage obtained from spacecraft

An exact analysis of the coverage obtained by spacecraft using cross-track scanning and nadir-centered conical imaging, under imposed viewing obliqueness and resolution requirements, is presented. In addition to exact expressions for the area acquired and the area acquisition rate, envelope theory is introduced to obtain the boundary of the imaged area. These expressions are relatively compact, allowing rapid machine computation. The effects of the sun phase angle, and of imaging system limitations are also examined. The Galileo mission encounter with Callisto is used as a numerical example, from which certain general conclusions are drawn regarding optimal imaging trajectories.     

The second order characteristic condition for plastic flow

In this paper the second order characteristic (discontinuous bifurcation) condition is derived for the granular flow (fully plastic) equations. This second order bifurcation equation is shown to be formally identical to the first order localization requirement during steady elastoplastic deformation provided the elastic compliance tensor is substituted for the product of the plastic multiplier with the flow Hessian. For isotropic yield and flow functions the invariant form of the characteristic condition is given in detail, as well as an alternative expression in adapted co‐ordinates. The characteristic condition can be regarded as defining a hardening function which is maximized to identify the critical angles. When the method is applied to 3D Coulomb flow, Mohr's 3D fracture plane conditions are obtained uniquely. Copyright © 2003 John Wiley & Sons, Ltd.     

Weibull statistical analysis of granite bending strength

Summary  This paper describes and discusses the adequacy of Weibull statistical analysis to analyse the bending strength of granite. The experimental results show that strength variability is related with a specific origin of failure. This conclusion is based on analysing the influence of the surface condition (extrinsic defects) on the bending strength results treated by the Weibull statistics. The conclusions drawn from this study have been validated by analysing the results of the critical flaw dimension estimated by applying the linear elastic fracture mechanics (LEFM) formulae. Results obtained from fractographic examination also have been used to describe the location of the origin of the fracture and understand the distribution of defects; i.e., there is a unimodal distribution of defects (intrinsic defects), despite the fact that some outlier values are normally observed in the fractured surfaces. Correspndence: P. M. Amaral, Department of Materials Engineering, Instituto Superior Técnico, Technical University of Lisbon, Av. Rovisco Pais, 1049-001 Lisboa, Portugal